Effects of LED Lights on Bulk Fill Resin Polymerization

The present study analyzed the microhardness and degree of conversion of three Bulk Fill resins (M1 - Filtek Bulk Fill; M2 - Tetric N-Ceram Bulk Fill and M3 - Opus Bulk Fill) polymerized by single peak and polywave Light-emitting Diode Curing Lights. A total 90 test specimens (n=10) were obtained using a Teflon matrix for the purpose of testing microhardness; and for degree of conversion: 135 specimens (n=5) by using a 2 x 6 cm matrix. The specimens were light polymerized using 3 light sources (L1 - Optilight Max, L2 - Bluephase, L3 - VALO). They were kept in artificial saliva om an oven at 37±1°C during the experiment. The degree of conversion was measured by FTIR 24 h after obtaining each test specimen. The microhardness readouts were performed with a microdurometer at the time intervals of 48 hours (T0), 7 days (T1), 14 days (T2) and 21 days (T3). M1L3 was found to show the highest microhardness values in T2, and M1 showed the lowest degree of conversion in the deep third with L1. It was concluded that Filtek Bulk Fill resin showed the best results in comparison with the other resins.

El presente estudio analizó la microdureza y el grado de conversión de tres resinas Bulk Fill (M1 - Filtek Bulk Fill; M2 - Tetric N-Ceram Bulk Fill y M3 - Opus Bulk Fill) polimerizadas por lámparas de curado de diodo emisor de luz de pico único y polionda. Se obtuvieron un total de 90 especímenes de prueba (n=10) utilizando una matriz de teflón con el propósito de probar la microdureza; y para grado de conversión: 135 especímenes (n=5) utilizando una matriz de 2 x 6 cm. Las muestras se fotopolimerizaron utilizando 3 fuen- tes de luz (L1 - Optilight Max, L2 - Bluephase, L3 - VALO). Se mantuvieron en saliva artificial en estufa a 37 ±1°C durante el experimento. El grado de conversión se midió por FTIR 24 h después de obtener cada muestra de prueba. Las lecturas de microdureza se realizaron con un microdurómetro en los intervalos de tiempo de 48 horas (T0), 7 días (T1), 14 días (T2) y 21 días (T3). Se encontró que M1L3 mostraba los valores más altos de microdureza en T2, y M1 mostraba el grado más bajo de conversión en el tercio profundo con L1. Se concluyó que la resina Filtek Bulk Fill mostró los mejores resultados en comparación con las demás resinas.

Changes in the properties of bulk-fill resins under conditions of gastroesophageal reflux and bulimia

Aim: Evaluate the roughness, microhardness and color change of different Bulk Fill resins when submitted to the condition of gastroesophageal reflux and bulimia. Methods: 60 specimens (n = 10) of Bulk-Fill composite resins were made: M1 ­ Filtek™; M2 ­ Tetric N-Ceram and M3 ­ OPUS, through a matrix 2x6 mm and light cured by the VALO light source. After polishing, initial analyzes (48 hours - T0) of surface roughness (Ra), microhardness (VHN) and color change (ΔE) were performed. To simulate the oral condition of severe gastroesophageal reflux and bulimia, the specimens were immersed in hydrochloric acid (S1) (pH 1.7) 4 minutes a day, for 7 days. Control group specimens were immersed in artificial saliva (S2). Subsequently to immersions, mechanical brushing was performed for 3 minutes, three times a day, simulating 7 days of brushing. And again, the analyzes of Ra, VHN and ΔE were performed (7 days - T1). Thus, hydrochloric acid immersion, mechanical brushing and Ra analysis were repeated at 14 days (T2) and 21 days (T3); and T2, T3 and T4 (3 years) for VHN and ΔE. Results: After Shapiro-Wilk statistical test, ANOVA and Tukey test with Bonferroni adjustment (p>0.05), M3 showed the lowest Ra at all times compared to the other resins, while the highest Ra was at T0. M1 and T1 showed higher VHN. And M2 and T4 showed higher ΔE. Conclusion: Bulk Fill resins can be indicated for patients with Gastroesophageal Reflux and Bulimia, nonetheless, Tetric N-Ceram resin showed the worst results

Influence of NaHCO3 powder on color and roughness of the composite submitted to bleaching and euterpe oleracea / Influencia del polvo de NaHCO 3 en el color y rugosidad del composite sometido a blanqueo y euterpe oleracea

Aim: This study aims to evaluate the surface roughness and susceptibility to staining of bleached composite resin with 22% carbamide peroxide, as well as the effect of subsequent prophylaxis with NaHCO3 powder. Material and Methods: Forty disk-shaped (2 × 6 mm) specimens of composite resin (Z250 XT) were prepared. Half of the specimens were subjected to bleaching with 22% carbamide peroxide, and the other half were stored in artificial saliva. In sequence, all specimens were immersed in acai juice (Euterpe oleracea) for 4 h for 14 days, and subdivided into two groups. Group 1 samples were subjected to prophylaxis treatment, while group 2 samples were subjected to treatment with artificial saliva. Surface roughness (Ra) and color (ΔE*) were measured after polishing (T0), bleaching (T1), immersion in acai juice (T2), and application of NaHCO3 powder (T3) using a profilometer and a spectrophotometer. Results: Statistical analyses (analysis of variance and Tukey's test, p≤0.05) revealed that regarding color there was statistically significance for the factors in isolation, except for the factor bleaching. For both color and surface roughness there was statistically significant difference for the interaction, except for the interaction between NaHCO3 power and bleaching. Conclusion: The NaHCO3 air-powder polishing decreases the staining of the composite resin; however, it increases the surface roughness. With respect to the color variable, the whitening factor had no significant effect on the tested material; however, it increases surface roughness.

Objetivo: Este estudio tiene como objetivo evaluar la rugosidad de la superficie y la susceptibilidad a la tinción de la resina compuesta blanqueada con peróxido de carbamida al 22%, así como el efecto de la profilaxis posterior con polvo de NaHCO3. Material y Métodos: Se prepararon cuarenta especímenes en forma de disco (2 × 6 mm) de resina compuesta (Z250 XT). La mitad de los especímenes se sometieron a blanqueo con peróxido de carbamida al 22% y la otra mitad se almacenó en saliva artificial. En secuencia, todos los especímenes se sumergieron en jugo de acai (Euterpe oleracea) durante 4h durante 14 días, y se subdividieron en dos grupos. Las muestras del grupo 1 se sometieron a tratamiento profiláctico, mientras que las muestras del grupo 2 se sometieron a tratamiento con saliva artificial. La rugosidad de la superficie (Ra) y el color (ΔE*) se midieron después del pulido (T0), el blanqueo (T1), la inmersión en jugo de acai (T2) y la aplicación de polvo de NaHCO3 (T3) utilizando un perfilómetro y un espectrofotómetro. Resultados: Los análisis estadísticos (análisis de varianza y prueba de Tukey, p≤0.05) revelaron que en relación al color hubo significancia estadística para los factores en forma aislada, excepto para el factor blanqueamiento. Tanto para el color como para la rugosidad de la superficie hubo una diferencia estadísticamente significativa para la interacción, excepto para la interacción entre el poder de NaHCO3 y el blanqueo. Conclusión: El pulido al aire con polvo de NaHCO3 disminuye el manchado de la resina compuesta; sin embargo, aumenta la rugosidad de la superficie. Con respecto a la variable color, el factor de blanqueamiento no tuvo efecto significativo sobre el material ensayado; sin embargo, aumenta la rugosidad de la superficie.

Effect of Color and Surface Roughness of Glass Ionomer Cements Submitted to Solutions Based on Ilex paraguariensis

ABSTRACT: The present study analyzed the color change (DE) and surface roughness (Ra) of glass ionomer cements (GICs) subjected to typical herbaceous South American beverage action - Ilex paraguariensis. 90 specimens (n = 10) were made: M1 - GIC Riva Light Cure® (SDI); M2 - GIC Riva Self Cure® (SDI); M3 - GIC Vitremer® (3M ESPE). After light curing/ polymerization of GICs, specimens were divided for being submitted to solutions for one hour a day for 21 days: S1 - Yerba Mate Pajarito Traditional (Pajarito); S2 - Erva Mate Chimarrão (Barão de Cotegipe); S3 - Water (control). Four DE and Ra readings were taken: T0 - initial; T1 - 7 days; T2 - 14 days and T3 - 21 days, with a spectrophotometer and a roughness meter respectively. The obtained data were submitted to ANOVA statistical analysis and Bonferroni. S1 and S2 at T1 and T2 there was no statistical difference between the materials, and at T3 Materials M1=M2, M1=M3, and M2>M3. For S3 at T1, T2 and T3 there was no difference between the materials. Analyzing surface roughness, there was no statistical significance. Concluded that all materials changed color with greater influence of time, but without changing surface roughness.

RESUMEN: En el presente estudio se analizó el cambio de color (DE) y la rugosidad superficial (Ra) de los cementos ionómero de vidrio (CIV) sometidos a la acción típica de las bebidas herbáceas sudamericanas - Ilex paraguariensis. Se realizaron 90 especímenes (n = 10): M1 - GIC Riva Light Cure® (SDI); M2 - GIC Riva Self Cure® (SDI); M3 - GIC Vitremer® (3M ESPE). Después de la fotopolimerización/ polimerización de los CIV, los especímenes se dividieron y fueron sometidos a soluciones durante una hora al día durante 21 días: S1 - Yerba Mate Pajarito Tradicional (Pajarito); S2 - Erva Mate Chimarrão (Barão de Cotegipe); S3 - Agua (control). Se tomaron cuatro lecturas de DE y Ra: T0 - inicial; T1 - 7 días; T2 - 14 días y T3 - 21 días, con espectrofotómetro y rugosímetro respectivamente. Los datos obtenidos fueron sometidos a análisis estadístico ANOVA y Bonferroni. S1 y S2 en T1 y T2 no hubo diferencia estadística entre los materiales y en T3 Materiales M1=M2, M1=M3 y M2>M3. Para S3 en T1, T2 y T3 no hubo diferencia entre los materiales. Al analizar la rugosidad de la superficie, no hubo significación estadística. En conclusion, todos los materiales cambiaron de color con mayor influencia del tiempo, pero sin cambiar la rugosidad de la superficie.

Effect of desensitizing dentifrices on eroded dentin wettability / Efeito de dentifrícios dessensibilizantes na molhabilidade da dentina erodida

Objective: To analyze the wettability on the surface of eroded dentin in teeth submitted to abrasive wear with desensitizing dentifrices. Material and Methods: Bovine dentin specimens were polished and immersed in 10 mL of citric acid (pH=3.2) for 2 h. The eroded specimens were submitted to mechanic brushing according to the 4 dentifrices adopted: Colgate Total (control); Colgate Sensitive Pro-Relief; Sensodyne Repair & Protect; or Sensodyne Rapid Relief. Afterwards, it was conditioned in 37% aqueous phosphoric acid solution. Wettability of 80 specimens (n=10) brushed for 7 or 21 days was evaluated by measuring the contact angle between the dentin surface and a drop of the adhesive Single Bond Universal® (3M) with a goniometer. Changes in the surface morphology of 12 specimens (n = 3) brushed for 21 days were followed by confocal laser scanning microscopy (CLSM). Data were analyzed by two-way ANOVA and Tukey test (p > 0.05). Results: Groups treated with desensitizing dentifrices did not differ significantly (p ≤ 0.05). Surface treatment and abrasive wear did not interact significantly (p ≤ 0.05). Brushing along 7 days gave the smallest contact angle value (p ≥ 0.05). CLSM images showed morphological changes for all the groups. Conclusion: The desensitizing dentifrices did not interfere in eroded dentin wettability after brushing along 7 or 21 days. Brushing with any of the dentifrices along 21 days promoted open dentinal tubules.(AU)

Objetivo: Analisar a aplicação de um adesivo na superfície de dentina erodida em dentes submetidos ao desgaste abrasivo com agentes dessensibilizantes. Material e Métodos: Espécimes de dentina bovina foram polidos e imersos em 10 mL de ácido cítrico (pH=3,2) por 2 h. Os espécimes erodidos foram submetidos à escovação mecânica de acordo com os 4 dentifrícios adotados: Colgate Total (controle); Colgate Sensitive Pro-Alívio; Sensodyne Repair & Protect; ou Sensodyne Rápido Alívio. Em seguida, foram condicionados em ácido fosfórico a 37%. A molhabilidade de 80 espécimes (n=10) escovados por 7 ou 21 dias foi avaliada medindo-se o ângulo de contato entre a superfície dentinária com uma gota do adesivo Single Bond Universal® (3M) por um goniômetro. Alterações na morfologia da superfície de 12 espécimes (n = 3) escovados por 21 dias foram seguidos por Microscopia Confocal de Varredura a Laser (MCVL). Os dados foram analisados por ANOVA dois fatores e teste de Tukey (p > 0,05). Resultados: Os grupos tratados com dentifrícios dessensibilizantes não diferiram significativamente (p ≤ 0,05). O tratamento de superfície e o desgaste abrasivo não interagiram significativamente (p ≤ 0,05). A escovação ao longo de 7 dias apresentou o menor valor de ângulo de contato (p ≥ 0,05). As imagens do MCVL mostraram alterações morfológicas para todos os grupos. Conclusão: Os dentifrícios dessensibilizantes não interferiram na molhabilidade da dentina erodida após escovação ao longo de 7 ou 21 dias. A escovação com qualquer um dos dentifrícios ao longo de 21 dias promoveu a abertura dos túbulos dentinários (AU)

Is there a preferable management for root caries in middle-aged and older adults? A systematic review.

Aim This systematic review aimed to critically summarise the results of clinical studies investigating agents able to: stop the progression of carious lesions; stop the development of new root carious lesions; preserve the vitality of the infected dental tissues; and increase the surface hardness or change of surface texture, in middle-age and older adults.Methods PubMed, Scopus, and Web of Science were searched systematically, following PRISMA guidelines. Clinical trials published from 2011 to 2020 (March) were included. This systematic review is registered in the PROSPERO database (CRD42018104399). Languages were restricted to English.Results Thirteen of 312 studies were eligible for this review. Eight agents were identified in the studies and their efficacy was assessed using different methods. The agents that presented valuable results on preventing or arresting root caries were 38% silver diamine fluoride (SDF), arginine-containing toothpaste and high-fluoride toothpastes.Conclusions Based on the selected studies' findings, annual applications of 38% SDF could be the most effective treatment for root caries in older adults. In addition, the daily use of a 1.5% arginine toothpaste or a high-fluoride toothpaste could also be recommended. More research on root caries-specific diagnostic methods, especially at very early stages, is necessary.

Microhardness and surface roughness of Biodentine exposed to mouthwashes.

Aim: This study evaluates Vickers microhardness and surface roughness in Biodentine cement (M1) and glass-ionomer cement Fuji IX (M2), both immersed in mouthwash. Materials and Methods: Fifty-four samples were randomly distributed in distilled water (S1), Listerine Cool Mint (S2), and Colgate Plax (S3). Each sample was put in a flask with mouthwash for 2 min, under vibration, twice a day for 21 days. Microhardness and surface roughness were assessed at 48 h (T0), 7 days (T1), 14 days (T2), and 21 days (T3). Results: For roughness: time (T), solution (S) and material (M), TxM, and SxM and for microhardness: M, TxS, TxM, and SxM were statistically significant. T3, M1, M1T3, and M1S1 presented the highest surface roughness. M2, M1T0, M1T1, M1T2, M1S1, and M1S2 presented higher microhardness. Conclusion: Biodentine showed higher surface roughness for T1, T2, and T3 and higher microhardness for T0, T1, and T2 against Fuji IX. Biodentine presented higher microhardness independently of solution.

Color evaluation of a resin cement light polymerized by different light sources and submitted to potentially staining beverages / Avaliação da cor de um cimento resinoso fotopolimerizado por diferentes fontes de luz e submetidos a bebidas potencialmente corantes

Introduction: The color stability of resin cements, whether dual-pre-cured or photopolymerizable, as well as the color of the dental substrate, are fundamental for the aesthetic success of ceramic restorations, since the ceramic presents a high level of translucency due to its small thickness. Objective: The aim of this in vitro study was to evaluate the color of a resin cement light polymerized by different light sources and immersed in potentially staining beverages. Material and method: Were made 42 specimens of resin cement Variolink-Esthetic (2×6mm) (n=7), being half polymerized with LED light (F1) and half with Halogen light (F2). The specimens were stored in artificial saliva at 37 °C±1 °C. After 24 hours, they were polished with abrasive discs, and divided for the purpose of being submitted to the different solutions for 2 minutes per day, for 28 days, as follows: S1 - Coca-Cola; S2 - Red Wine; and S3 - Distilled Water (Control). Five color readouts were taken: T0 - initial; T1 - 7 days; T2 - 14 days; T3 - 21 days; and T4 - 28 days; with a spectrophotometer (Model SP62S). The color change data (ΔE*) were submitted to statistical analysis, ANOVA and Tukey (p≤0.05). Result: Analyzing the factor solution, S2 (5.89 (±0.02)), produced a higher ΔE* value than S1 (3.79 (±0.02)) and (S1), a higher value than S3 (1.41 (±0.02)). Analyzing the factor light source, F2 (4.05 (±0.12)), produced a higher ΔE* value than F1 (3.33 (±0.12)). When analyzing the factor time, ΔE* values were found to increase gradually over the course of time: T1(2.36 (±0.08)); T2(3.27 (±0.08)); T3(4.06 (±0.08)); and T4(5.09 (±0.08)). Conclusion: It was concluded that red wine produced a greater color change; Halogen light promoted highest degree of pigmentation; and the longer the time of immersion, the greater the color change of the material.

Introdução: A estabilidade de cor dos cimentos resinosos, sejam eles de presa dual ou fotopolimerizáveis, assim como a cor do substrato dental, são fundamentais para o sucesso estético das restaurações cerâmicas uma vez que a cerâmica apresenta alto nível de translucidez devido a sua pequena espessura. Objetivo: O objetivo deste estudo in vitro foi avaliar a cor de um cimento resinoso fotopolimerizado por diferentes fontes de luz e imersos em bebidas potencialmente corantes. Material e método: Foram confeccionados 42 espécimes do cimento resinoso Variolink-Esthetic (2×6mm) (n=7), sendo metade fotopolimerizado com luz LED (F1) e metade com luz Halógena (F2). Os espécimes foram mantidos em saliva artificial à 37 °C±1 °C. Após 24 horas, foram polidos com discos abrasivos e subdivididos para serem imersos 2 minutos por dia, durante 28 dias, nas diferentes soluções: S1 - Coca-Cola; S2 - Vinho Tinto; e S3 - Água destilada (controle). Foram realizadas 5 leituras de cor: T0 - inicial; T1 - 7 dias; T2 - 14 dias; T3 - 21 dias; e T4 - 28 dias; com auxílio de um espectrofotômetro (modelo SP62S). Os dados de alteração de cor (ΔE*) foram submetidos a análise estatística, ANOVA e Tukey (p≤0,05). Resultado: Analisando o fator solução, S2 (5,89 (±0,02)), proporcionou maior ΔE* que S1 (3,79 (±0,02)) e este (S1), maior que S3 (1,41 (±0,02)). Analisando o fator fonte de luz, F2 (4,05 (±0,12)), proporcionou maior ΔE* que F1 (3,33 (±0,12)). E analisando o fator tempo, obteve-se que ΔE* foi gradativamente aumentando no decorrer do tempo: T1(2,36 (±0,08)); T2(3,27 (±0,08)); T3(4,06 (±0,08)); e T4(5,09 (±0,08)). Conclusão: Conclui-se que o vinho tinto promoveu maior alteração de cor; a luz Halógena promoveu maior pigmentação e; quanto maior o tempo de imersão, maior alteração de cor do material.

Bond strength of resin cements to novel materials to intracanal posts applications / Resistência de união de cimentos resinosos a novos materiais para pinos intrarradiculares

Objective: Evaluate the bond strength of resin cements to new materials for application in intraradicular posts. Material and Methods: Five materials were evaluated: fiberglass, PET, polyethylene, polyacetal and PTFE. Two commercial resin cements (Rely X U200 and Rely X Arc) were applied on the test specimens of the materials (9x3mm) and the bonding was evaluated through the shear bond strength test, where the chisel operated with a load of 1kN and a velocity of 0.5mm/min at the cement/material interface. The data were analyzed by the Shapiro-Wilk test, followed by the two-way analysis of variance, performed with the Bonferroni post-test (α=0.05). Results: The glass fiber was statistically different from all evaluated materials (p0.05). Comparing the two cements, a statistical difference was found between Rely X U200 and Arc only for the glass fiber (p=0). Conclusion: PET, polyethylene, polyacetal and PTFE exhibited reduced bond strength compared to the glass fiber (AU)

Objetivo: Avaliar a resistência de união de cimentos resinosos a novos materiais para aplicação em pinos intrarradiculares. Material e método: Foram avaliados cinco materiais: fibra de vidro, PET, polietileno, poliacetal e PTFE. Dois cimentos resinosos comerciais (Rely X U200 e Rely X Arc) foram aplicados sobre os corpos de prova dos materias (9x3mm) e a resistência de união foi avaliada através do teste de cisalhamento, onde o cinzel atuou com carga de 1kN e velocidade de 0,5mm/min na interface cimento/material. Verificada a normalidade dos dados através do teste Shapiro-Wilk, foi realizada a análise de variância de dois fatores com pós-teste de Bonferroni (α=0,05). Resultados: a fibra de vidro foi diferente estatisticamtente de todos os materiais avaliados (p0,05). Comparando-se os dois cimentos, foi encontrada diferença estatística entre o Rely X U200 e Arc apenas para a fibra de vidro (p=0). Conclusão: PET, polietileno, poliacetal e PTFE apresentaram resistência de união reduzida comparando-se à fibra de vidro. (AU)

Evaluación in vitro de la rugosidad superficial y la alteración de color de dos tipos de ionómeros de vidrio, luego de ser sometidos a diferentes bebidas / Avaliação in vitro da rugosidade superficial e alteração de cor de dois tipos de ionômeros de vidro, depois de ter sido submetido a bebidas diferentes / in vitro evaluation of surface roughness and color alteration of two types of glass ionomers, after being subjected to different beverages

El objetivo de este estudio in vitro fue analizar la rugosidad superficial y la alteración de color de dos tipos de ionómeros vítreos luego de ser sometidos a diferentes soluciones. En una matriz de teflón (8x2mm), fueron confeccionados 60 cuerpos de prueba con 2 tipos de ionómeros fotopolimerizables: 30 para el Fuji II LC (M1) y otros 30 para el Ketac N100 (M2). El aparato utilizado fue el Elipar Freelight 2 3M Espe. La fotopolimerización se realizó por 20 segundos cada cuerpo de prueba. Luego de la confección, los sesenta cuerpos de prueba fueron mantenidos en gasa humedecida por 24 hs en estufa a 37ºC y luego se clasificaron y luego se dividieron en tres grupos de 10 cada uno para ser sometidos a 3 tipos diferentes de soluciones: agua destilada (S1), bebida carbonatada (S2) y jugo cítrico (S3) por 90 segundos diariamente durante 14 días. Las lecturas de la alteración de color, obtenidas a través de un colorímetro, y las de rugosidad superficial, realizadas por medio del rugosímetro, fueron realizadas a las 48 hs. (T0) y luego a los 14 días (T1). Los resultados obtenidos fueron sometidos al test ANOVA y Tukey (p≤0.05). Los resultados mostraron que; a) La bebida carbonatada (S2) tuvo mayor media de alteración de color (ΔE*) en relación a las otras soluciones, b) que Ketac N100 (M2) tuvo mayor media con respecto a la rugosidad superficial en la interacción material por solución. Por tanto, se concluyó que trascurrido determinado período de tiempo las propiedades estéticas y físico-mecánicas de los materiales estudiados se ven afectados.

O objetivo deste estudo in vitro foi analisar a rugosidade superficial e a alteraçã o de cor de dois tipos de ionômeros de vidrio após serem submetidos a diferentes bebidas. Em uma matriz de te ón (8x2mm), foram confeccionados 60 corpos de prova com 2 tipos de ionômeros fotopolimerizáveis: 30 para o Fuji II LC (M1) e outros 30 para o Ketac N100 (M2). O aparelho utilizado foi o Elipar Freelight 2 3M Espe. A fotopolimerização foi realizada por 20 segundos em cada corpo de prova. Após a confecçã o, os 60 corpos de prova foram mantidos em gaze umedecida por 24 hrs em estufa a 37o C e divididos em 3 grupos de 10 cada um, para ser submetidos a 3 tipos diferentes de soluçõ es: água destilada (S1), bebida carbonatada (S2) e suco cítrico (S3) por 90 segundos diariamente durante 14 dias. As leituras de alteraçã o de cor, obtidas através de um colorímetro, e das de rugosidades superficial, realizadas por meio do rugosímetro, foram realizadas após 48 hs. (T0) e após 14 dias (T1). Os resultados obtidos foram submetidos à test ANOVA e Tukey (p≤0.05). Os resultados mostraram que; a) a bebida carbonatada (S2) teve maior media de alteraçã o de cor (ΔE*) em relaçã o às outras soluçõ es, b) que Ketac N100 (M2) teve maior media com respeito a rugosidade superficial na interaçã o material pela soluçã o. Podemos concluir que a partir de determinado período de tempo as propriedades estéticas e físico-mecânicas dos materiais estudados são afetadas.

The aim of this in vitro study was to examine the surface roughness and discoloration of two types of glass ionomer had been subjected to different solutions. In a matrix of Teflon (8x2mm), 60 test bodies were prepared with 2 types of resin modified glass ionomers: 30 for Fuji II LC® (M1) and the other 30 for Ketac N100® (M2). The apparatus was Freelight two 3M ESPE Elipar. Photopolymerization was carried out for 20 second each test body. After the preparation, the seventy-two specimens were kept in gauze soaked for 24 hours in an oven at 37°C and then were sorted and divided into three groups of 12 each to be subjected, for 90 seconds each day at 3 different types of solutions: distilled water (S1), carbonated beverage (S2) and citrus juice (S3) for 14 days. Readings from discoloration, obtained through a colorimeter, and the surface roughness made using the profilometer were performed after 48 hours (T0) and after day 14 (T1). The results were submitted to ANOVA and Tukey test (p ≤ 0.05). The results showed that: a) The carbonated beverage (S2) had higher mean discoloration (ΔE *) compared to the other solutions, b) Ketac N100®(M2) had higher mean with respect to the interaction surface roughness material solution. Therefore, it was concluded that certain period of time elapsed aesthetic properties and physico-mechanical properties of the material studied are affected.

Antimicrobial potential of Casearia sylvestris against oral bacteria / Potencial antimicrobiano da Casearia sylvestris frente a bactérias orais

Aim: The aim of this study was to obtain Casearia sylvestris leave extracts by different extractive methods, including the obtention of essential oil, in order to compare their antimicrobial activities to conventional mouthwash chlorhexidine against oral bacteria. Material and method: For this evaluation, extracts from the leaves were obtained by different methods of extraction (infusion, decoction, maceration and percolation) using different solvent systems: water 100%, ethanol 100%, methanol 100%, water: ethanol 3:7; water: ethanol 7:3; water: methanol 7:3 and water: methanol 3:7. The essential oil, which corresponds to a volatile fraction, was obtained by hydrodistillation using Clevenger modified apparatus. The microdilution broth method was used to determine the values of minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) for the following microorganisms: Streptococcus mutans ATCC 25175, S. mitis ATCC 49456, S. sanguinis ATCC 10556, S. salivarius ATCC 25975, Lactobacillus casei ATCC 11578 and Enterococcus faecalis ATCC4082. Chlorhexidine gluconate was used as a positive control. Result: All extracts evaluated in the used protocol displayed MIC values higher than 400 µg/mL and few showed bactericidal activity. The antimicrobial activity of essential oil was higher than the activity of the extracts, and the best minimum inhibitory concentration and minimum bactericidal concentration values were obtained against L. casei (MIC of 0.023 µg/mL and MBC of 0.046 µg/mL) and S. mutans (MIC of 25 µg/mL and MBC of 50 µg/mL), respectively. Conclusion: The essential oil of Casearia sylvestris has significant antimicrobial activity against oral microorganisms.

Objetivo: O objetivo deste estudo foi obter extratos por diferentes métodos de extração de Casearia sylvestris, incluindo a obtenção de óleo essencial, a fim de comparar suas atividades antimicrobianas em relação aos enxaguatórios bucais convencionais com clorexidina contra bactérias orais. Material e método: Para esta avaliação, extratos das folhas foram obtidos por diferentes métodos de extração (infusão, decocção, maceração e percolação) utilizando diferentes sistemas de solventes: 100% de água, 100%, de etanol, metanol 100%, água: etanol 3: 7; água: etanol 7: 3; água: metanol 7: 3 e água: metanol 3: 7. O óleo essencial, que corresponde a uma fração volátil, foi obtido por hidrodestilação usando o aparelho de Clevenger modificado. O método de microdiluição em caldo foi usado para determinar os valores de concentração inibitória mínima (MIC) e a concentração bactericida mínima (MBC) para os seguintes microrganismos: Streptococcus mutans ATCC 25175, ATCC 49456 S. mitis, S. sanguinis ATCC 10556, S. salivarius ATCC 25975, Lactobacillus casei ATCC 11578 e Enterococcus faecalis ATCC4082. Gluconato de clorexidina foi usada como um controle positivo. Resultado: Todos os extratos avaliados no protocolo utilizado apresentaram valores de MIC superior a 400 ug/mL e alguns mostraram atividade bactericida. A atividade antimicrobiana do óleo essencial foi maior do que a atividade dos extratos, e a melhor concentração inibitória mínima e valores de concentração bactericida mínima foram obtidos contra L. casei (MIC de 0,023 ug/mL e MBC de 0,046 ug/mL) e S. mutans (MIC de 25 ug/mL e MBC de 50 ug /mL), respectivamente. Conclusão: O óleo essencial de Casearia sylvestris tem atividade antimicrobiana significativa contra microrganismos orais.

Surface roughness of composite resins subjected to hydrochloric acid.

The purpose of this study was to determine the influence of hydrochloric acid on surface roughness of composite resins subjected to brushing. Sixty samples measuring 2 mm thick x 6 mm diameter were prepared and used as experimental units. The study presented a 3x2 factorial design, in which the factors were composite resin (n=20), at 3 levels: microhybrid composite (Z100), nanofilled composite (FiltekTM Supreme), nanohybrid composite (Ice), and acid challenge (n=10) at 2 levels: absence and presence. Acid challenge was performed by immersion of specimens in hydrochloric acid (pH 1.2) for 1 min, 4 times per day for 7 days. The specimens not subjected to acid challenge were stored in 15 mL of artificial saliva at 37 oC. Afterwards, all specimens were submitted to abrasive challenge by a brushing cycle performed with a 200 g weight at a speed of 356 rpm, totaling 17.8 cycles. Surface roughness measurements (Ra) were performed and analyzed by ANOVA and Tukey test (p≤0.05). Surface roughness values were higher in the presence (1.07±0.24) as compared with the absence of hydrochloric acid (0.72±0.04). Surface roughness values were higher for microhybrid (1.01±0.27) compared with nanofilled (0.68 ±0.09) and nanohybrid (0.48±0.15) composites when the specimens were not subjects to acid challenge. In the presence of hydrochloric acid, microhybrid (1.26±0.28) and nanofilled (1.18±0,30) composites presents higher surface roughness values compared with nanohybrid (0.77±0.15). The hydrochloric acid affected the surface roughness of composite resin subjected to brushing.

Surface Roughness of Composite Resins Subjected to Hydrochloric Acid

The purpose of this study was to determine the influence of hydrochloric acid on surface roughness of composite resins subjected to brushing. Sixty samples measuring 2 mm thick x 6 mm diameter were prepared and used as experimental units. The study presented a 3x2 factorial design, in which the factors were composite resin (n=20), at 3 levels: microhybrid composite (Z100), nanofilled composite (FiltekTM Supreme), nanohybrid composite (Ice), and acid challenge (n=10) at 2 levels: absence and presence. Acid challenge was performed by immersion of specimens in hydrochloric acid (pH 1.2) for 1 min, 4 times per day for 7 days. The specimens not subjected to acid challenge were stored in 15 mL of artificial saliva at 37 oC. Afterwards, all specimens were submitted to abrasive challenge by a brushing cycle performed with a 200 g weight at a speed of 356 rpm, totaling 17.8 cycles. Surface roughness measurements (Ra) were performed and analyzed by ANOVA and Tukey test (p≤0.05). Surface roughness values were higher in the presence (1.07±0.24) as compared with the absence of hydrochloric acid (0.72±0.04). Surface roughness values were higher for microhybrid (1.01±0.27) compared with nanofilled (0.68 ±0.09) and nanohybrid (0.48±0.15) composites when the specimens were not subjects to acid challenge. In the presence of hydrochloric acid, microhybrid (1.26±0.28) and nanofilled (1.18±0,30) composites presents higher surface roughness values compared with nanohybrid (0.77±0.15). The hydrochloric acid affected the surface roughness of composite resin subjected to brushing.

Este estudo avaliou a influencia do ácido clorídrico na rugosidade superficial de resinas compostas submetidas a escovação. Sessenta corpos de prova medindo 2 mm de espessura x 6 mm de diâmetro foram confeccionados e utilizados como unidades experimentais. O presente estudo envolve uma análise fatorial 3x2, onde os fatores foram resina composta (n=20), com 3 níveis: resina composta microhíbrida (Z100), nanoparticulada (Filtek TM Supreme) e nanohíbrida (Ice); e desafio ácido (n=10), com 2 níveis: ausência e presença. O desafio ácido foi realizado por meio da imersão em ácido clorídrico (pH 1,2) por 4 h diárias, 1 min cada imersão, durante 7 dias. Os espécimes que não foram submetidos ao desafio ácido foram armazenados em 15 mL de saliva artificial a 37 °C. Todos os espécimes foram submetidos ao desafio abrasivo. O processo de escovação foi realizado com 200 g de peso, com velocidade de 356 rpm, totalizando 17,8 ciclos. As medidas de rugosidade superficial (Ra) foram realizadas e analisadas por meio da ANOVA e teste de Tukey (p<0,05). Os valores de rugosidade superficial foram maiores na presença (1,07±0,24)quando comparado com a ausencia do ácido hidroclorídrico (0,72±0,04). A resina microhíbrida (1,01±0,27) apresentou maior rugosidade superficial que as resinas nanoparticulada (0,68±0,09) e nanohíbrida (0,48±0,15) quando os espécimes não foram submetidos ao desafio ácido. Na presença do ácido hidroclorídrico, a resina microhíbrida (1,26±0,28) e a resina nanoparticulada (1,18±0,30) apresentou maior valor de rugosidade superficia comparado com a resina nanohíbrida (0.77±0.15). O ácido hidroclorídrico influenciou a rugosidade superficial da resina composta submetida a escovação.

The influence of mouthrinses and simulated toothbrushing on the surface roughness of a nanofilled composite resin

The aim of this study was to determine the influence of mouthrinses on the surface roughness of a nanofilled composite resin after toothbrushing. One hundred nanofilled composite resin specimens were prepared and randomly distributed into two groups-brushed and non-brushed-and then assigned to five subgroups, according to the mouthrinse solutions (n = 10): Colgate Plax Fresh Mint, Oral B, Cepacol, Colgate Plax, and artificial saliva. Each sample was immersed in 20 mL of the mouthrinses for 1 minute, 5 days per week, twice a day, for a 3-week period. The control group used in the study was one in which the specimens were not subjected to brushing and remained only in artificial saliva. Toothbrushing was performed once a week for 1 minute, for 3 weeks. Surface roughness measurements (Ra) were performed after the immersion period and toothbrushing, by means of a profilometer. Data were analyzed by two-way ANOVA and Tukey's test. Analysis revealed that the association between toothbrushing and Colgate Plax Fresh Mint produced the lowest surface roughness (p < 0.05). All other groups tested (Oral B, Cepacol, Colgate Plax, artificial saliva) exhibited no statistically significant differences between surfaces, whether subjected to toothbrushing or not (p < 0.05). It was concluded that the surface roughness of the nanofilled composite resin tested can be influenced by the mouthrinse associated with toothbrushing.

The influence of mouthrinses and simulated toothbrushing on the surface roughness of a nanofilled composite resin.

The aim of this study was to determine the influence of mouthrinses on the surface roughness of a nanofilled composite resin after toothbrushing. One hundred nanofilled composite resin specimens were prepared and randomly distributed into two groups-brushed and non-brushed-and then assigned to five subgroups, according to the mouthrinse solutions (n = 10): Colgate Plax Fresh Mint, Oral B, Cepacol, Colgate Plax, and artificial saliva. Each sample was immersed in 20 mL of the mouthrinses for 1 minute, 5 days per week, twice a day, for a 3-week period. The control group used in the study was one in which the specimens were not subjected to brushing and remained only in artificial saliva. Toothbrushing was performed once a week for 1 minute, for 3 weeks. Surface roughness measurements (Ra) were performed after the immersion period and toothbrushing, by means of a profilometer. Data were analyzed by two-way ANOVA and Tukey's test. Analysis revealed that the association between toothbrushing and Colgate Plax Fresh Mint produced the lowest surface roughness (p < 0.05). All other groups tested (Oral B, Cepacol, Colgate Plax, artificial saliva) exhibited no statistically significant differences between surfaces, whether subjected to toothbrushing or not (p < 0.05). It was concluded that the surface roughness of the nanofilled composite resin tested can be influenced by the mouthrinse associated with toothbrushing.

Efecto de diferentes técnicas de pulido y refrigeración en la rugosidad superficial de una resina nanohíbrida / Effect of different techniques of cooling and polishing the surface roughness of a composite resin nanohíbrida

El objetivo de este trabajo in vitro fue evaluar la rugosidad superficial de una resina compuesta nanohíbrida (Tetric N Ceram®) utilizando 3 técnicas de acabado superficial, con y sin refrigeración. Materiales y método: Fueron confeccionados 60 especimenes (n=10), obtenidos por medio de una matríz metálica (10 x 2 mm). Los especímenes fueron almacenados durante 24 horas en agua destilada a temperatura ambiente, siendo posteriormente divididos en 6 grupos: G1- astropol + refrigeración, G2-astrobrush + refrigeración, G3- astropol + astrobrush + refrigeración, G4-astropol sin refrigeración, G5-astrobrush sin refrigeración, G6- astropol + astrobrush sin refrigeración. La lectura de la rugosidad superficial (Ra) fue realizada 24 horas luego de los respectivos tratamientos por medio de un rugosímetro marca Mitutoyo, tipo SJ - 201P (Japón). Resultados: Los datos fueron sometidos al test de ANOVA (p?0,05) y demostraron que no existe diferencias estadísticamente significantes entre las diferentes técnicas de pulido y refrigeración. Conclusión: La técnica de pulido y refrigeración no interfiere en la rugosidad superficial, por tanto se debe tener en consideración las demás propiedades físicas de las resinas compuestas y el aspecto biológico del diente

The study evaluated in vitro the surface roughness in a nanohibrid composite resin (Tetric N Ceram®) polished with the use three polishing techniques with and without refrigeration. Materials and Methods: Sixty discs (n=10), was made with aid of a metal matrix measuring 10 x 2 mm. The specimens were stored in artificial saliva in an oven at 37oC (±1 oC), for 24 hours. After this time the specimens were submitted to action of astropol + refrigeration (G1), astrobrush + refrigeration (G2), astropol + astrobrush + refrigeration(G3), astropol whithout refrigeration (G4), astrobrush whithout refrigeration (G5), astropol + astrobrush whithout refrigeration (G6). The surface roughness (Ra) of the specimens was avaliated after 24 hours using profilometer (Mitutoyo SJ - 201P - Japon). Results: the data were submitted to Analysis of Variance ANOVA (p?0,05) and were no statistically significant differences detected for each technique. Conclusion: The effect polishing techniques and refrigeration not interferance in the surface roughness, but needed consideration of others properties

Influence of the occlusal alteration in the mandible morphology of the gerbil / Influencia de la alteración oclusal en la morfología mandibular del jerbo

Considering the biomechanical aspects, many facts need to be understood on the mandible, to know which effects unilateral occlusal changes may cause on the stomatognathic system. The aim of this study was to analyze the malocclusion by unilateral teeth extraction on the mandible morphology in gerbil. We used 10 gerbils Meriones unguiculatus, young male, weighing around 50-60g, divided into two groups (n=5), an experimental group and control, which evaluated the two hemi-mandibles, with a total of 20 samples which were measured by digital pachymeter. The measures were taken: (1) length and (2) width of the mandible condyle and (3) body height in the region of mandibular 1st molar. Data from these measurements were analyzed using ANOVA and Mann-Whitney test. The results of this study showed a statistically significant difference in the three measures between experimental and control groups. The width of the mandible head (condyle) showed statistical difference between the ipsilateral and contralateral sides to teeth extraction. It was concluded that the mastication modification by unilateral teeth extraction caused an imbalance, promoting not only a modification in the craniofacial growth pattern, but also a harmful effect on the stomatognathic system of the gerbil used as an experimental model in this study.

Considerando los aspectos biomecánicos, muchos hechos deben ser entendidos sobre la mandíbula, haciendo necesario comprender cuales son los efectos que pueden causar una alteración oclusal unilateral en el sistema estomatognático. El objetivo de este estudio fue analizar la maloclusión por la extracción de los dientes unilaterales sobre la morfología de la mandíbula en el gerbo. Se utilizaron 10 gerbos Meriones unguiculatus, machos jóvenes, con un peso aproximado de 50-60g, divididos en dos grupos (n = 5), un grupo experimental y otro control, en los cuales se evaluaron las dos hemimandíbulas, totalizando 20 muestras que fueron medidas con un caliper digital. Las medidas tomadas fueron: (1) longitud y (2) ancho del cóndilo mandibular, y (3) la altura del cuerpo en la región de los primeros molares mandibulares. Los datos de estas mediciones se analizaron mediante la prueba ANOVA y Mann-Whitney. Los resultados de este estudio mostraron una diferencia estadísticamente significativa en las tres medidas entre los grupos experimental y control. El ancho de la cabeza de la mandíbula (cóndilo) mostró una diferencia estadística entre los lados ipsilaterales y contralaterales a la extracción dentaria. Se concluyó que existe una alteración unilateral de la masticación inducida por la extracción de dientes unilateralmente, causando un desequilibrio y promoviendo no sólo una modificación en el patrón de crecimiento craneofacial, sino también un efecto nocivo obre el sistema estomatognático del gerbo utilizado como modelo experimental en este estudio.

Estudio comparativo de la microdureza de composites en relación a la fuente de luz, profundidad de polimerización y tiempo / Comparative study of microhardness of composites in relation to the light source, depth of cure and time

Evaluar la microdureza de las resinas Charisma (microhíbrida) y Z100 (híbrida) en relación a la profundidad de polimerización (8, 6, 4, 2 mm e 0 mm-superficial), la fuente de luz (Diodo emisión de luz-LED y Luz halógena de cuarzo-tungsteno-QTH) y los tiempos de análisis (inmediato, 24 h y 1 mes). Fueron testadas resinas Charisma (Kulzer) y Z100 (3M/ESPE). Para la realización del ensayo de microdureza fueron confeccionados 07 cuerpos de prueba de 8x2x4mm en matriz de carbono, con incrementos de 1mm cada y fotopolimerizados con los aparatos Optilux (Dabi Atlante) y LED (MMOptic). Los cuerpos de prueba fueron sometidos a los ensayos de dureza Vickers; inmediato, 24 horas y 1 mes después de la confección, almacenados en agua destilada y estufa a 37 1ºC. El análisis de microdureza fue realizada por medio del microdurómetro Shimadzu HMV-2000, con 5s de indentación y 500g de peso. La dureza fue evaluada en diferentes profundidades (superficie externa, 2, 4, 6 y 8 mm). Los resultados fueron estadísticamente significantes (p=5%) para todas las condiciones experimentales. Ambas resinas tuvieron la microdureza disminuida conforme el aumento de la profundidad y presentaron valores mayores con el aparato de luz halógena que con el aparato de diodo. La resina Z100 presento mayores valores de microdureza en relación a la resina Charisma. De acuerdo con los resultados, se puede concluir que cuanto mayor la profundidad menor la dureza y el aparato QTH proporcionó mayor grado de polimerización

To evaluate the microhardness of the resins Charisma (microhybrid) and Z100 (hybrid) in respect to the depth of polymerization (8, 6, 4, 2 mm and 0 mm-superficial), the source of light (Emitting Diode of light-LED and halogenous quartz-tungsten-QTH Light) and the analysis times (immediate, 24 h and 1 month). Resins Charisma (Kulzer) and Z100 were tested (3M/ESPE). For the accomplishment of the microhardness essay 07 were confectioned body-of-test of 8x2x4mm in carbon matrix, with increments of 1mm each and photopolymerised with Optilux devices (Dabi Atlante) and LED (MMOptic). The body-of-test was submitted to the essays of Vickers hardness; immediate, 24 hours and 1 month after the confection, stored in distiled water and heat 37±1ºC. The microhardness analysis was accomplished by means of the microdurometer Shimadzu HMV-2000, with 5s and 500g of load. The hardness was evaluated in different depths (external surface, 2, 4, 6 and 8 mm). The results were statistically significant (p=5%) for all the experimental conditions. Both resins had had the microhardness diminished as the increase of the depth and had presented bigger values with the device of halogenous light that with the diode device. The Z100 resin presented greaters values of microhardness in respect to the Charisma resin. In accordance with the results, it can be concluded that how much bigger the depth lesser the hardness and device QTH provided to greater polymerization degree

Influence of NaHCO3 powder on translucency of microfilled composite resin immersed in different mouthrinses.

UNLABELLED: The regular use of mouthrinses, particularly when combined with the use of air-powder polishing, could affect the appearance of tooth-colored restorations. The current study sought to evaluate the effect of NaHCO(3) powder on translucency of a microfilled composite resin immersed in different mouthrinses, at distinct evaluation periods. Eighty disk-shaped specimens of composite resin (Durafill VS, Heraeus Kulzer GmbH & Co. KG, Hanau, Germany) were prepared. The composite specimens were then randomly allocated into two groups according to the surface treatment: exposure to NaHCO3 powder (10 seconds) or nonexposure, and they were randomly assigned into four subgroups, according to the mouthrinses employed (N = 10): Periogard (Colgate/Palmolive, São Bernardo do Campo, SP, Brazil), Cepacol (Aventis Pharma, São Paulo, SP, Brazil), Plax (Colgate/Palmolive), and distilled water (control group). The samples were immersed for 2 minutes daily, 5 days per week, over a 4-month test period. Translucency was measured with a transmission densitometer at seven evaluation periods. Statistical analyses (analysis of variance and Tukey's test) revealed that: distilled water presented higher translucency values (86.72%); Periogard demonstrated the lowest translucency values (72.70%); and Plax (74.05%) and Cepacol (73.32%) showed intermediate translucency values, which were statistically similar between them (p > 0.01). NaHCO3 air-powder polishing increased the changes in translucency associated with the mouthrinses. Air-powder polishing alone had no effect on material translucency. Translucency percent was gradually decreased from 1 week of immersion up to 4 months. It may be concluded that the NaHCO3 powder and the tested mouthrinses have affected the translucency of microfilled composite resin, according to the tested time. CLINICAL SIGNIFICANCE: During the last decade, the demand for composite resin restorations has grown considerably, however, controversy persists regarding the effect of surface roughness on color stability.

Resistência flexural e rugosidade superficial de resinas acrílicas utilizadas para confecção de placas oclusais / Flexural strength and superficial roughness of acrylic resins used for confection of occlusal splints

O objetivo deste trabalho foi avaliar in vitro o efeito da adição de fibras de vidro na resistência flexural por três pontos e rugosidade superficial de resinas utilizadas para a confecção de placas oclusais. Para este estudo, foram utilizadas as seguintes resinas com diferentes tipos de polimerização: resina acrílica autopolimerizável Vipi Flash® (RA), resina acrílica termopolimerizável por banho de água Vipi Cril® (RT) e resina acrílica termopolimerizável por calor de microondas Vipi Wave® (RM),com e sem adição de fibras de vidr (FV). Hipóteses em estudo: a adição de fibras de vidro aumenta a resistência flexural por três pontos e a rugosidade superficial dos corpos-de-prova. Foram confeccionadas doze amostras (n = 12) para cada grupo, a partir de uma matriz metálica com 67 mm de comprimento x 12,60 mm de largura x 3,00 mm de espessura. Os corpos-de-prova foramsubmetidos ao teste de resistência flexural em máquina de ensaio universal (EMIC DL 2000®), a uma velocidadede 5 mm/min, e ao teste de rugosidade superficial em rugosímetro (Mitutoyo®). Os dados foram submetidos à análise de variância e ao teste complementar de Tukey (p < 0,01). De acordo com os resultados, em relação à resistência flexural (MPa) houve diferença estatisticamente significativa somente para o fator tipo de polimerização das resinas (RA = 81,54 ± 4,94, RT = 92,86± 16,85, RM = 86,24 ± 8,89). Em relação à rugosidade superficial (RA-μm), houve diferença para os dois fatores fatores avaliados: tipo de polimerização (RA = 0,10 ± 0,02, RT = 0,13 ± 0,03, RM = 0,11 ± 0,13) e adição de fibras de vidro (CF = 0,13 ± 0,02, SF = 0,10 ± 0,11). Pode-se concluir que a adição de fibras de vidro aos grupos experimentais não alterou os valores de resistência flexural, no entanto aumentou os valores de rugosidade superficial das amostras testadas